82LM LiftMaster Chamberlain Sears Craftsman Garage Door Opener Remote Control Coding Instructions

LIFTMASTER PROFESSIONAL

MODEL 82LM Two-Function Remote Control

The push buttons on the Two-Function remote controls can activate garage door openers, entry ways and /or light controls. (Instructions for programming light products are included with those accessories).

Code switch remote controls are used when several persons are operating the same device. Code switches must be set to matching positions. In all remote controls used to operate the same receiver.   Use the “smooth” push button, exclusively for code switch application. Follow the instructions described. 

*************   WARNING   *************

            Moving Door can cause serious injury or death.

·         DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.

·         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

·         Keep people clear of opening while door is moving.

·         DO NOT allow children to play with the transmitter or door operator.

          If safety reverse does not work properly:

·         Close door then disconnect operator using the manual release handle.

·         DO NOT use transmitter or door operator.

·         Refer to Door and Door Operators Owner’s Manuals before attempting any repairs.

_________________________________________________

            Electrical Shock can cause serious injury or death.

·         Power cord must be unplugged before attaching any wires,

·         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

***************************************************************************************************************

Program smooth push button (code switch application)

Your code block with dip switches can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find code block with dip switches).

1. Slide back the battery compartment cover on the bottom of the remote control housing.
2. Place the old and new remote controls side by side. Make sure you set code switches 1 through 9 in all remotes to matching positions. Use a pen or screwdriver to move the switches to (+), (-) or (0).
3. Replace the battery compartment cover.

Program ribbed push button (Green “learn” button)

1. Press and release the “learn” button on the motor unit. . This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button). The learn indicator light will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the button on the hand-held remote.
3. Release the button when the motor light unit light blinks. It has learned the code. If the light bulbs are no installed, two clicks will be heard.

To Erase ALL Codes from Motor Unit Memory

To deactivate any unwanted remote, first erase all codes:

Press and hold the “learn” button on motor unit until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use.

The Remote Control Battery

The 12V battery should produce power for at least a year. If the green test light is dim or does not come on, replace the battery.

To change the battery, slide back the battery compartment cover. Position the new battery as indicated. Replace compartment cover.

Home | Remote Controls | Keyless Entry | Repair Parts | Wall Controls | Rail Extension Kits | Accessories | Coding Instructions | Customer Assistance | Remote Compatibility | Board Compatibility | Order by Phone, Fax or Check | Compatible Brand Names | Site Index | About Us

"100% Secure Online Ordering"
Fast shipping via USPS Priority Mail (2-4 day delivery)
Only $6.95 per order!"

Sears Craftsman, Chamberlain, LiftMaster, Master Mechanics, Wayne Dolton and all other Brands of Garage Door openers are registered tradenames of the respective entities and are only used for reference

Copyright © 2001-2008
1st Garage Door Openers Inc.

Copyright © 2008 All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.